Melt Pump
- Polymer extrusion melt gear pump
- melt pump for plastic extrusion
- Polymer Reaction Kettle pump
- gear pump rubber extruder
- melt pumps for extrusion
- Melt Gear Pumps for BOPP Films
- ZB-G bearing external melt pump
- melt pump for pvc extrusion
- ZB double shaft drive melt pump
- Explanation of terms for melt pump d
- ZB-X Series chemical gear melt pump
- PID Control System for extrusion
- PLC Control System for extruder
- ZB-U series melt extrusion spinning
- ZB-E series transfer melt pump for e
- ZB-H series high temperature and hig
- ZB-R series gear melt pump for rubbe
- ZB-K series chemical stainless steel
- ZB-D series pipeline melt pump for p
- ZB-F series melt pump for reaction k
- ZB-B series dosing standard thermopl
- ZB-C series plastic granule machine
Screen Changer
- polymer melt filtration screen changer
- recycled plastic screen changer
- slide plate screen changer
- pillar screen changer
- dual bolt screen changer
- continuous screen changer
- screen changer polymer filter
- Plastic extruder filter extrusion sc
- Biodegradable plastic PBAT/PLA hydra
- Single plate hydraulic screen change
- plastic extrusion screen changer
- single plate hydraulic quick screen
- Manual control screen changer
- Double plate continuous hydraulic sc
- Automatic mesh belt continuous scree
- Double piston four screen cavities c
- Single plate double screen cavities
- Single piston double screen cavities
- Double piston four screen cavities b
- Dual Bolt double screen cavities hyd
Feeding System
- force feeder extruder
- loss in weight feeder for masterbatc
- continuous feeding system
- Liquid loss in weight feeder
- china volumetric screw doser feeder
- Multi-component loss in weight feede
- Micro loss in weight metering feeder
- Single screw gravimetric dosing feed
- Twin screw loss in weight metering f
melt blown progress
contact us
- Batte Machinery Zhengzhou Co., Ltd.
- E-mail: sale@meltpump.com
- whatsapp: +86 158 38331071
- Tel: +86-371-67991755 / 67992755
- FAX:+86-371-67993277
- Address:No.11 Changchun Road, High-tech Zone, Zhengzhou, China.
News
- Why Are Screen Changers Installed in
- The control of the melt pump speed n
- Introduction to the Basic Structure
- Analysis of the Structure and Functi
- Application, Structure, and Technica
- Melt Pump: The Secret Weapon on the
- What are the roles of the metering p
- Structure, Performance, and Applicat
- dual-column screen changer in the me
- Screen Changer Selection Strategy Ba
What are the debugging steps for the hydraulic screen changer of the granulator?
1. Set the temperature of each zone of the screen changer of the granulator (this screen changer type is a plate-type double-station screen changer) to the expected value.
2. Turn on all power sources and start to heat up. After the temperature of each zone of the screen changer of the granulator reaches the set value, the whole machine is kept for 40-60 minutes.
3. Reconfirm whether the flange of the screen changer of the granulator and the pressure sensor are locked.
4. Press the "Start" button on the operating handle of the hydraulic station to start the hydraulic station.
plastic granulator screen changer
5. Long press the "push" button of the operating handle of the hydraulic station until the screen changer reciprocating plate is completely pushed out of the screen changer body and then release it. (The remote net block of the hydraulic cylinder completely leaks out of the main body of the screen changer)
6. Long press the "pull" button of the operating handle of the hydraulic station until the screen changer slide plate is pulled back to its original position and then released. (The proximal net block of the hydraulic cylinder completely leaks out of the main body of the screen changer)
7. Jog the "Stop" button of the operating handle to shut down the hydraulic station.
8. Wipe the mesh block and the position of the mesh block on the reciprocating board to confirm that there is no debris and oil stains.
9. Put the net block correctly. The front face of the net block should be about 1 mm lower than the plane of the reciprocating plate.
batte melt pump factory
10. Insert the mesh correctly. The edges of the mesh should all be submerged in the groove at the front end of the mesh, and the highest point of the mesh should not be higher than the plane of the reciprocating plate.
11. Repeat steps 4, 5, 7, 8, 9, and 10 in order to complete the installation of the mesh block and mesh piece at the other end of the hydraulic screen changer of the granulator.
12. The whole machine of the granulator screen changer keeps heat for 20 minutes.
13. Feeding and start-up production.
Previous：How to choose a screen changer that suits your needsNext：Selection of ABS granulation filter screen changer