Melt Pump
- Polymer extrusion melt gear pump
- melt pump for plastic extrusion
- Polymer Reaction Kettle pump
- gear pump rubber extruder
- melt pumps for extrusion
- Melt Gear Pumps for BOPP Films
- ZB-G bearing external melt pump
- melt pump for pvc extrusion
- ZB double shaft drive melt pump
- Explanation of terms for melt pump d
- ZB-X Series chemical gear melt pump
- PID Control System for extrusion
- PLC Control System for extruder
- ZB-U series melt extrusion spinning
- ZB-E series transfer melt pump for e
- ZB-H series high temperature and hig
- ZB-R series gear melt pump for rubbe
- ZB-K series chemical stainless steel
- ZB-D series pipeline melt pump for p
- ZB-F series melt pump for reaction k
- ZB-B series dosing standard thermopl
- ZB-C series plastic granule machine
Screen Changer
- polymer melt filtration screen changer
- recycled plastic screen changer
- slide plate screen changer
- pillar screen changer
- dual bolt screen changer
- continuous screen changer
- screen changer polymer filter
- Plastic extruder filter extrusion sc
- Biodegradable plastic PBAT/PLA hydra
- Single plate hydraulic screen change
- plastic extrusion screen changer
- single plate hydraulic quick screen
- Manual control screen changer
- Double plate continuous hydraulic sc
- Automatic mesh belt continuous scree
- Double piston four screen cavities c
- Single plate double screen cavities
- Single piston double screen cavities
- Double piston four screen cavities b
- Dual Bolt double screen cavities hyd
Feeding System
- force feeder extruder
- loss in weight feeder for masterbatc
- continuous feeding system
- Liquid loss in weight feeder
- china volumetric screw doser feeder
- Multi-component loss in weight feede
- Micro loss in weight metering feeder
- Single screw gravimetric dosing feed
- Twin screw loss in weight metering f
melt blown progress
contact us
- Batte Machinery Zhengzhou Co., Ltd.
- E-mail: sale@meltpump.com
- whatsapp: +86 158 38331071
- Tel: +86-371-67991755 / 67992755
- FAX:+86-371-67993277
- Address:No.11 Changchun Road, High-tech Zone, Zhengzhou, China.
News
- Why Are Screen Changers Installed in
- The control of the melt pump speed n
- Introduction to the Basic Structure
- Analysis of the Structure and Functi
- Application, Structure, and Technica
- Melt Pump: The Secret Weapon on the
- What are the roles of the metering p
- Structure, Performance, and Applicat
- dual-column screen changer in the me
- Screen Changer Selection Strategy Ba
Precautions for Vertical Installation of Extruder Melt Gear Pump
The installation method of the power input shaft of the extruder hot melt gear pump perpendicular to the horizontal plane is called vertical installation of the pump shaft, and the installation example is shown in the following figure. The installation process requires attention to the following issues
1. The connection head of the pump melt gear pump for plastic extruder is correctly installed on the input shaft. After adjusting the depth of the joint used to connect the universal joint on the connection head and fully exposing it, tighten the top screw to fix the connection head
2. When installing the melt pump body and reducer, check and adjust the radial deviation between the center of the melt pump power input shaft and the center of the reducer power output shaft; (0.5mm-1.8mm)
Installation of Extruder Melt Gear Pump
3. When installing the universal joint, the flange of the universal joint should be fully installed into the joint joint mouth, and the connecting bolts should be installed and tightened after the two ends are fitted together
4. When installing the universal joint, pull out the axial length of 2mm to 5mm for installation, and do not allow the melt pump extruder shaft and reducer pump shaft to be squeezed. Angular deviation after installation of universal joint coupling< (1 ° -2 °)
5. The melt pump body of the screw extruder and the melt gear pump is hard connected. After the production line is started, the working temperature of the extruder increases, and the screw is prone to thermal expansion and elongation, resulting in displacement of the melt pump body. After the production line has fully warmed up to the working temperature, the pump body should be checked for displacement, the pump body position should be readjusted, and the gear pump installation bolts should be tightened.
Previous：Application and technical parameters of micro reaction kettle pumpNext：Application, structure, working principle, and classification of melt pumps