Melt Pump
- Polymer extrusion melt gear pump
- melt pump for plastic extrusion
- Polymer Reaction Kettle pump
- gear pump rubber extruder
- melt pumps for extrusion
- Melt Gear Pumps for BOPP Films
- ZB-G bearing external melt pump
- melt pump for pvc extrusion
- ZB double shaft drive melt pump
- Explanation of terms for melt pump d
- ZB-X Series chemical gear melt pump
- PID Control System for extrusion
- PLC Control System for extruder
- ZB-U series melt extrusion spinning
- ZB-E series transfer melt pump for e
- ZB-H series high temperature and hig
- ZB-R series gear melt pump for rubbe
- ZB-K series chemical stainless steel
- ZB-D series pipeline melt pump for p
- ZB-F series melt pump for reaction k
- ZB-B series dosing standard thermopl
- ZB-C series plastic granule machine
Screen Changer
- polymer melt filtration screen changer
- recycled plastic screen changer
- slide plate screen changer
- pillar screen changer
- dual bolt screen changer
- continuous screen changer
- screen changer polymer filter
- Plastic extruder filter extrusion sc
- Biodegradable plastic PBAT/PLA hydra
- Single plate hydraulic screen change
- plastic extrusion screen changer
- single plate hydraulic quick screen
- Manual control screen changer
- Double plate continuous hydraulic sc
- Automatic mesh belt continuous scree
- Double piston four screen cavities c
- Single plate double screen cavities
- Single piston double screen cavities
- Double piston four screen cavities b
- Dual Bolt double screen cavities hyd
Feeding System
- force feeder extruder
- loss in weight feeder for masterbatc
- continuous feeding system
- Liquid loss in weight feeder
- china volumetric screw doser feeder
- Multi-component loss in weight feede
- Micro loss in weight metering feeder
- Single screw gravimetric dosing feed
- Twin screw loss in weight metering f
melt blown progress
contact us
- Batte Machinery Zhengzhou Co., Ltd.
- E-mail: sale@meltpump.com
- whatsapp: +86 158 38331071
- Tel: +86-371-67991755 / 67992755
- FAX:+86-371-67993277
- Address:No.11 Changchun Road, High-tech Zone, Zhengzhou, China.
News
- Why Are Screen Changers Installed in
- The control of the melt pump speed n
- Introduction to the Basic Structure
- Analysis of the Structure and Functi
- Application, Structure, and Technica
- Melt Pump: The Secret Weapon on the
- What are the roles of the metering p
- Structure, Performance, and Applicat
- dual-column screen changer in the me
- Screen Changer Selection Strategy Ba
Characteristics of the structural design of bushings for melt gear pumps
The sleeve for melt gear pump is characterized in that a flow-guiding groove for melt infiltration is provided on the inner bore wall of the sleeve, and a reflux groove is provided on one side wall and the outer side wall of the sleeve. The flow-guiding groove, the groove opening on the cavity side of the melt gear pump is the big end, and the big end is deeper and wider than the small end of the groove opening near the cover side. The flow-conducting groove extends from the large end to the small end with a certain degree of curvature, and the groove opening at the large end gradually extends from a deeper and wider groove opening to a shallower and narrower groove opening at the small end.
One end of the reflux groove is close to the small end of the reflux groove but not connected through, the reflux groove extends from one side wall of the sleeve to the outer side wall of the sleeve. Shaft sleeve pair symmetrically set up corresponds to the active shaft and the slave shaft, two shaft sleeve return groove corresponds to set up, the return groove forms the return hole.
Using the structure of the sleeve set in the pump body of the active shaft and the slave shaft, sleeve and shaft to do the relative rotation movement, a small part of the melt in the pump body through the large end of the guide groove infiltration into the sleeve inside the wall to play a good lubrication, infiltration into the guide groove melt from the small end of the guide groove outflow into the reflux groove in the same vicinity of the part of the self-lubrication of the melt in the pump inside and outside of the role of the pressure difference back to the pump cavity, to realize a self-lubricating cycle, to achieve a self-lubricating cycle, to achieve a self-lubricating cycle. Realize a self-lubricating cycle, can reduce the wear of the sleeve and shaft, to maintain the long-term stable operation of the melt gear pump.
Email: info@battemachinery.com
WhatsApp: +86 158 38331071
Previous：Steps in the use of melt pumpsNext：Do you know about melt pumps for sheet film extrusion?