Melt Pump
- Polymer extrusion melt gear pump
- melt pump for plastic extrusion
- Polymer Reaction Kettle pump
- gear pump rubber extruder
- melt pumps for extrusion
- Melt Gear Pumps for BOPP Films
- ZB-G bearing external melt pump
- melt pump for pvc extrusion
- ZB double shaft drive melt pump
- Explanation of terms for melt pump d
- ZB-X Series chemical gear melt pump
- PID Control System for extrusion
- PLC Control System for extruder
- ZB-U series melt extrusion spinning
- ZB-E series transfer melt pump for e
- ZB-H series high temperature and hig
- ZB-R series gear melt pump for rubbe
- ZB-K series chemical stainless steel
- ZB-D series pipeline melt pump for p
- ZB-F series melt pump for reaction k
- ZB-B series dosing standard thermopl
- ZB-C series plastic granule machine
Screen Changer
- polymer melt filtration screen changer
- recycled plastic screen changer
- slide plate screen changer
- pillar screen changer
- dual bolt screen changer
- continuous screen changer
- screen changer polymer filter
- Plastic extruder filter extrusion sc
- Biodegradable plastic PBAT/PLA hydra
- Single plate hydraulic screen change
- plastic extrusion screen changer
- single plate hydraulic quick screen
- Manual control screen changer
- Double plate continuous hydraulic sc
- Automatic mesh belt continuous scree
- Double piston four screen cavities c
- Single plate double screen cavities
- Single piston double screen cavities
- Double piston four screen cavities b
- Dual Bolt double screen cavities hyd
Feeding System
- force feeder extruder
- loss in weight feeder for masterbatc
- continuous feeding system
- Liquid loss in weight feeder
- china volumetric screw doser feeder
- Multi-component loss in weight feede
- Micro loss in weight metering feeder
- Single screw gravimetric dosing feed
- Twin screw loss in weight metering f
melt blown progress
contact us
- Batte Machinery Zhengzhou Co., Ltd.
- E-mail: sale@meltpump.com
- whatsapp: +86 158 38331071
- Tel: +86-371-67991755 / 67992755
- FAX:+86-371-67993277
- Address:No.11 Changchun Road, High-tech Zone, Zhengzhou, China.
News
- Why Are Screen Changers Installed in
- The control of the melt pump speed n
- Introduction to the Basic Structure
- Analysis of the Structure and Functi
- Application, Structure, and Technica
- Melt Pump: The Secret Weapon on the
- What are the roles of the metering p
- Structure, Performance, and Applicat
- dual-column screen changer in the me
- Screen Changer Selection Strategy Ba
Solution to overload of melt pump motor
During the operation of the melt pump, occasional challenges and difficulties may arise, such as motor overload. We have conducted a thorough analysis of the causes of this issue and summarized corresponding strategies to help users better understand and respond.
When the density or viscosity of the medium sucked in by the melt pump is too high, the motor may be overloaded. At this point, we can restore the normal operation of the motor by adjusting the specific gravity or viscosity of the medium to meet the working requirements of the pump.
If the pressure difference of the outlet filter is too large, it will also cause the motor to bear excessive load. We should regularly inspect and clean the outlet filter to ensure that it is unobstructed and provides a stable working environment for the motor.
3. Bending of the motor shaft is also an issue that cannot be ignored. Once the shaft bends, the load on the motor will increase. Therefore, we need to regularly check the condition of the shaft, and if any bending is found, it should be repaired or replaced immediately.
4. Tight packing can also bring additional load to the motor. In this case, we only need to adjust the tightness of the packing appropriately to restore normal operation of the motor.
5. Of course, the malfunction of the electric motor itself is also a cause of overload. At this point, we should promptly repair or replace the motor to avoid further deterioration of the problem.
6. Excessive coaxiality of the coupling can also affect the operation of the motor. In order to ensure the normal operation of the motor, we need to regularly calibrate the coupling to ensure that its coaxiality meets the requirements.
7. Excessive discharge pressure may also be one of the reasons for motor overload. To solve this problem, we can appropriately reduce the pressure at the discharge port to allow the motor to operate within a more reasonable working range.
In summary, there are various reasons for the overload of the melt pump motor, and we need to conduct detailed analysis and treatment according to the specific situation. Only in this way can the stable operation of the melt pump be ensured and its service life be extended.
Email: info@battemachinery.com
WhatsApp: +86 158 38331071
Previous：Characteristics and configuration scheme of plate hydraulic screen changerNext：What are the differences between a melt pump and an extrusion line?