Melt Pump
- Polymer extrusion melt gear pump
- melt pump for plastic extrusion
- Polymer Reaction Kettle pump
- gear pump rubber extruder
- melt pumps for extrusion
- Melt Gear Pumps for BOPP Films
- ZB-G bearing external melt pump
- melt pump for pvc extrusion
- ZB double shaft drive melt pump
- Explanation of terms for melt pump d
- ZB-X Series chemical gear melt pump
- PID Control System for extrusion
- PLC Control System for extruder
- ZB-U series melt extrusion spinning
- ZB-E series transfer melt pump for e
- ZB-H series high temperature and hig
- ZB-R series gear melt pump for rubbe
- ZB-K series chemical stainless steel
- ZB-D series pipeline melt pump for p
- ZB-F series melt pump for reaction k
- ZB-B series dosing standard thermopl
- ZB-C series plastic granule machine
Screen Changer
- polymer melt filtration screen changer
- recycled plastic screen changer
- slide plate screen changer
- pillar screen changer
- dual bolt screen changer
- continuous screen changer
- screen changer polymer filter
- Plastic extruder filter extrusion sc
- Biodegradable plastic PBAT/PLA hydra
- Single plate hydraulic screen change
- plastic extrusion screen changer
- single plate hydraulic quick screen
- Manual control screen changer
- Double plate continuous hydraulic sc
- Automatic mesh belt continuous scree
- Double piston four screen cavities c
- Single plate double screen cavities
- Single piston double screen cavities
- Double piston four screen cavities b
- Dual Bolt double screen cavities hyd
Feeding System
- force feeder extruder
- loss in weight feeder for masterbatc
- continuous feeding system
- Liquid loss in weight feeder
- china volumetric screw doser feeder
- Multi-component loss in weight feede
- Micro loss in weight metering feeder
- Single screw gravimetric dosing feed
- Twin screw loss in weight metering f
melt blown progress
contact us
- Batte Machinery Zhengzhou Co., Ltd.
- E-mail: info@battemachinery.com
- whatsapp: +86 158 38331071
- Tel: +86 371 67991755
- After-sales Tel: +86 371 67997677 / 67997877
- Address:No.11 Changchun Road, High-tech Zone, Zhengzhou, China.
News
- What are the vulnerable parts of the
- What is a dual drive rubber gear pum
- Application, Characteristics, and Co
- Characteristics of melt pumps (meter
- Do you know about the hot melt adhes
- Selection scheme of hydraulic screen
- Working principle of plastic rubber
- 150cc extruder melt pump for spunbon
- Application and characteristics of r
- pvc granulate extruder melt pump
The state of sliding bearings affects the working efficiency of melt pumps
BATTE melt pump will introduce you to the melt flow rate volume method.
Melt volume flow rate refers to the volume of molten plastic passing through a standard die under a certain load and piston action at a fixed position at a fixed temperature. The result is converted into the volume of plastic extruded every 10 minutes, in cm ³/ 10 minutes.
thermoplastic melt pump
When using a melt index meter to test the melt flow rate, the volume method (MVR) can be used for testing. The main method for testing the melt flow rate using the volume method is to measure the volume of the melt flowing through the die per unit time. There are two testing methods:
1. Measure the distance the piston moves within the specified time. Start timing after the piston enters the range of the ring marking, record the movement range of the piston after the timing time, and then calculate the melt volume flow rate.
plastic extusion melt pump
2. Measure the time taken for the piston to move a specified distance. Set a moving distance within the range of the ring marking of the piston rod, and measure the time it takes for the piston rod to move this distance.
These two methods ultimately need to be converted into the volume of melt flow per unit time.
Email: info@battemachinery.com
WhatsApp: +86 158 38331071
Previous：Installation standard for shaft seal of polymer reactor melt pumpNext：Application of Melt Metering Pump in PGA Industry