Melt Pump
- Polymer extrusion melt gear pump
- melt pump for plastic extrusion
- Polymer Reaction Kettle pump
- gear pump rubber extruder
- melt pumps for extrusion
- Melt Gear Pumps for BOPP Films
- ZB-G bearing external melt pump
- melt pump for pvc extrusion
- ZB double shaft drive melt pump
- Explanation of terms for melt pump d
- ZB-X Series chemical gear melt pump
- PID Control System for extrusion
- PLC Control System for extruder
- ZB-U series melt extrusion spinning
- ZB-E series transfer melt pump for e
- ZB-H series high temperature and hig
- ZB-R series gear melt pump for rubbe
- ZB-K series chemical stainless steel
- ZB-D series pipeline melt pump for p
- ZB-F series melt pump for reaction k
- ZB-B series dosing standard thermopl
- ZB-C series plastic granule machine
Screen Changer
- polymer melt filtration screen changer
- recycled plastic screen changer
- slide plate screen changer
- pillar screen changer
- dual bolt screen changer
- continuous screen changer
- screen changer polymer filter
- Plastic extruder filter extrusion sc
- Biodegradable plastic PBAT/PLA hydra
- Single plate hydraulic screen change
- plastic extrusion screen changer
- single plate hydraulic quick screen
- Manual control screen changer
- Double plate continuous hydraulic sc
- Automatic mesh belt continuous scree
- Double piston four screen cavities c
- Single plate double screen cavities
- Single piston double screen cavities
- Double piston four screen cavities b
- Dual Bolt double screen cavities hyd
Feeding System
- force feeder extruder
- loss in weight feeder for masterbatc
- continuous feeding system
- Liquid loss in weight feeder
- china volumetric screw doser feeder
- Multi-component loss in weight feede
- Micro loss in weight metering feeder
- Single screw gravimetric dosing feed
- Twin screw loss in weight metering f
melt blown progress
contact us
- Batte Machinery Zhengzhou Co., Ltd.
- E-mail: sale@meltpump.com
- whatsapp: +86 158 38331071
- Tel: +86-371-67991755 / 67992755
- FAX:+86-371-67993277
- Address:No.11 Changchun Road, High-tech Zone, Zhengzhou, China.
News
- Why Are Screen Changers Installed in
- The control of the melt pump speed n
- Introduction to the Basic Structure
- Analysis of the Structure and Functi
- Application, Structure, and Technica
- Melt Pump: The Secret Weapon on the
- What are the roles of the metering p
- Structure, Performance, and Applicat
- dual-column screen changer in the me
- Screen Changer Selection Strategy Ba
Working principle of plastic rubber extruder melt pump
The working principle of the extrusion melt pump is to transport the melt by the change in working volume caused by the meshing of the main and driven gears. Firstly, the extruder melt pump is a positive displacement conveying device, and the flow rate is strictly proportional to the pump speed. It mainly consists of pump casing, driving gear, driven gear, sliding bearings, front and rear end plates, packing seals, etc. During work, the molten material is transported by the change in working volume caused by the meshing of the main and driven gears.
Specifically, when the gear rotates in the specified direction, the melt enters the grooves of the two gears in the feed area. As the gears rotate, the melt is brought into the feeding area from both sides. The re meshing of gears causes the molten material in the tooth groove to be squeezed out of the discharge area and pushed to the outlet pipeline. As long as the pump shaft rotates, the gear will press the melt towards the outlet side, so the pump outlet can reach a very high pressure, and there are no high requirements for the inlet flow rate and pressure, and even the inlet vacuum suction can be achieved.
In addition, the extruder melt pump also has the function of boosting and isolating pressure. When the material at the outlet of the extrusion melt pump is subjected to resistance generated by the forming mold, the gears in the extruder melt pump act like pistons in a cylinder, exerting a squeezing effect on the melt in the discharge area, achieving the pressure boosting function of the extruder melt pump. At the same time, the gears in the pump act as a rotating barrier, effectively blocking the impact of pressure and flow fluctuations in the feed area on the discharge area.
In general, the extruder melt pump achieves continuous discharge, metering, and pressurization of the melt through volumetric conveying and pressure isolation, and is widely used in industries such as plastic, resin, and rubber extrusion molding. During use, it is necessary to monitor the melt pump to a certain extent, including outlet pressure, suction pressure, inlet and outlet pressure difference, motor current, gear shaft sealing, and pump temperature, to ensure its normal operation.
Email: info@battemachinery.com
WhatsApp: +86 158 38331071
Previous：150cc extruder melt pump for spunbond machineNext：Selection scheme of hydraulic screen changer for PE pipe extruder